Top 3 Reasons Why Your Car AC is Not Blowing Cold Air

Auto AC Repair - ac not blowing air

During the hot summer months in Utah you want your vehicle's AC to blow cool refreshing air for your comfort and the comfort of your passengers. There are a variety of reasons why your car AC is not blowing cold air. Fixing the AC could be as simple as recharging your car's AC refrigerant or repairing a refrigerant leak but may also require complex electrical climate control repair or slipping compressor clutch to get your air conditioning operating at top performance once again.

Understanding Your Vehicle's AC System

The air conditioning system in your vehicle can be complex due to the location of the hoses and lines. Essentially, your vehicle's AC system compresses and heats the refrigerant, then allowing it to decompress and condense into a liquid that causes it to rapidly lose heat. This process absorbs heat from the car's cabin and is continuously repeated to achieve your desired temperature.

The basic concept is much easier to understand when the components are broken down, as follows:

  • The compressor runs off an engine belt that squeezes or compresses the gaseous refrigerant.
  • Once it has been pressurized, the condenser cools it down through a series of finned tubes where it returns to a liquid state. This liquid will then pass through a dryer or receiver that removes excess water to eliminate the risk of ice crystal formations inside the AC system.
  • Next the liquid refrigerant enters the evaporator via a thermal expansion valve where it is then exposed to heat from the vehicle's cabin. At this point the fluid boils, reducing it to a gas form once again. During this process the heat from the surrounding air is absorbed causing the evaporator coil to chill. Finally, it is redistributed throughout the cabin by the blowing fan through the vents as cool, crisp air-conditioned air.

Just about every car has the same basic AC parts consisting of a compressor, condenser and evaporator that work together to keep you cool during the warm summer months. When any of these parts fail, you're left with uncomfortable heat that a rolled-down window just can't fix.

Here are the top 3 reasons why your car AC may not be blowing cold air:

#1 Your Car's AC Needs a Recharge

The most common cause of a vehicle's air conditioner not getting cold enough is that it needs to be recharged. You can recharge your refrigerant by yourself, but to save time and make sure the job is done correctly you should make an appointment with your local professional auto shop.

The trusted professionals at Ace Auto in West Jordan, Utah can help you recharge your car's AC system. Give us a call at 801-447-1693 for a free quote to get you back on the road with the comfort and safety with a recharged AC blowing crisp, cool air again.

#2 An AC System Refrigerant Leak

When your vehicle's AC system develops a refrigerant fluid leak it can be challenging to detect due to the fact that refrigerant fluid instantly evaporates when it comes in contact with air. A professional mechanic uses specialized tools to determine if there is a leak by introducing ultraviolet fluid to show signs of low refrigerant pressure in the AC system. Signs of an AC system refrigerant leak:

  • Audible click when the AC is turned on.
  • AC cycles on and off frequently.
  • Hissing sounds from the AC system (when the engine is off).
  • Oil residue around AC pipe fittings and hoses.

A refrigerant leak repair may include repairing or replacing the specific failing component. If a large amount of fluid has been lost, your AC system will need to be flushed and the refrigerant fluid will need to be replaced to function properly and get the cool air flowing. *Please note that refrigerant is a very harmful toxic chemical and should not be handled without the proper equipment operated by a trained professional.

#3 Fan Motor Failure

Another common source of trouble in your car's AC system might be the fan(s) motor located at the front of the vehicle's motor. Whether your car has one or two fans, it is important that the fan is in good working order to both keep you cool and to provide vital cooling to your engine.

If you are unsure about the correct diagnosis of your car's failing air conditioner, the friendly and caring certified mechanics at Ace Auto in West Jordan, Utah will give you a free repair quote and work quickly to fix your AC and get you back out on the road.

Professional Help from Ace Auto to Keep You and Your Passengers Comfortable with Cool Air

If your car ac unit is not blowing cold enough air in Utah , contact the ASE certified auto mechanics at Ace Auto in West Jordan Utah to quickly inspect and repair your AC unit. For an honest AC diagnosis and speedy repairs in West Jordan, schedule an AC repair appointment at Ace Auto or call 801-447-1693 for a FREE repair quote. Our ASE Certified master mechanics are experienced technicians that are certified and can repair any AC system problem and have your AC working properly again.

Download PDF

Save Your Engine By Maintaining Your Fuel Injectors

Mechanic Working On A Car

Are you burning through tanks of gas faster than you used to? Finding it harder to speed up to get around the nice old lady going 35mph on the highway? Having issues with your engine sputtering when you slow down? When was the last time you had your fuel injectors looked at? Keeping your fuel injection system well-maintained is one of the keys to better fuel performance for your car and a longer life for your engine.

Why Do Fuel Injectors Matter?

Your car’s fuel injection system consists of two primary parts: the fuel injectors and the fuel pump. The fuel pump sends pressurized fuel from the gas tank to the car’s engine bay. The injectors then distribute the fuel to different cylinders within the engine as a fine spray. Your spark plugs ignite the spray from the injectors, powering your car.

Computers control modern fuel injection systems, replacing the manual carburetors found in most cars built before 1990. Carburetors required time to warm-up before the car was ready to drive. Modern systems improve upon this performance by allowing cars to start up right away without needing this warm-up period, even in cold weather.

Fuel injection systems also improve the fuel efficiency of your car. A well-maintained system limits the amount of gas needed to power the car, giving you better mileage for every tank of gas. They also make less noise than old carburetor-powered engines and lead to less engine maintenance as your car parts last longer in this type of system.

Fuel Injection Maintenance

There are two primary ways to clean and maintain fuel injection systems:

On-Car Cleaning

These are a less-intensive way of cleaning injection systems. Nothing is taken apart or removed; instead, cleaners are introduced to remove contaminants from the system.

  • Method 1: Additives get poured directly into the fuel tank. They flow through the fuel system, eventually reaching the injectors and working to remove impurities.
  • Method 2: A pressurized canister of injector cleaner gets attached to the car’s fuel rail. The engine runs off of the cleaner instead of the fuel, giving the injectors a more thorough cleaning.

Off-Car Cleaning

The injectors get removed from your car entirely and cleaned with special ultrasonic tools. They’re then tested to ensure that the flow rate and spray pattern are within acceptable limits. Technicians also check for possible leaks before putting the injectors back into your car.

Fuel Injector Wear And Tear

You suck in dirt and other contaminants every time you drive your car. Over time, those contaminants get into your engine. When too much of it gets pulled into your injector and fuel pump, your car begins experiencing problems including:

  • A lack of acceleration when you step on your gas pedal
  • You start burning through gas faster every time you fill up
  • There’s a noticeable unevenness when you let your engine idle

Continued failure to maintain your car’s fuel injection system often leads to major damage to your engine, costing you a lot of money in repairs.

Check Your Fuel Injectors Today at Ace Auto in West Jordan, Utah

Think you might have an issue with your car’s fuel injection system? Contact Ace Auto in West Jordan, Utah today and schedule a review of your injection system. We’ll make sure your engine runs as efficiently as possible. Give our master mechanics a call today at 801-447-1693 for a free quote on your next service!

Download PDF

5 Warning Signs Your Car Needs a New Timing Belt

Man Looking Troubled Under the Cars Hood

Man Looking Troubled Under the Cars Hood

Prevention is the Best Solution

Your vehicle's mileage is the best indicator a new timing belt is needed. Most of us don't even think about it until there's a problem, but there are warning signs for a bad timing belt that you shouldn't ignore. Most commonly you will notice symptoms while trying to start your car or if it's making funny noises and acting-up while running. Since vehicle manufacturers provide specific mileage for timing belt replacement, and prevention is the best solution. If you already suspect your car needs a new timing belt, have it checked before time runs out.

Check Your Owner's Manual

Because the timing belt is responsible for turning your engine's cam and crankshaft in sync, it is subject to incredible exertion and typically needs to be replaced within 60,000 - 100,000 miles, depending on the manufacturer's recommendation. Check your owner's manual for exact mileage recommendations on your specific vehicle. There are only a few warning indicators that can help you diagnose a weak or loose timing belt, but there are no obvious clues to indicate a worn belt that may be close to snapping.

It's About Time to Replace Your Timing Belt

Since the timing belt is absolutely essential to the safe operation of your vehicle, please have an experienced mechanic inspect it if you think something is wrong. Listed below are five signs to be aware of that may help determine if it's about time to replace your timing belt:

  • What's That Sound? - One sound that you need to be aware of is a high-pitched screech or whirring when you first start your car and/or when you're idling or accelerating. The next is a ticking coming from inside the engine itself. These are both possible indicators that the timing belt is malfunctioning.
  • Between 2000 - 4000 RPM - An engine that starts acting up when you reach between 2000 - 4000 RPM could be failing to function normally because the timing belt is loose or breaking down from wear and tear. This may cause the belt to 'slip' while accelerating.
  • Heavy Exhaust Fumes - If you notice more smoke and fumes than normal coming from the exhaust, this could be another indication that your timing belt is overdue for a replacement. The engine running with a malfunctioning belt can cause excessive exhaust fumes.
  • Engine Will Not Turn Over - When you try to start your car, can hear the starter motor but the engine will not turn over in addition to any of the above warning signs - it is quite possible that damage has been done to the engine as a result of a broken or snapped timing belt.
  • Car Stops Working Abruptly - This is the worst-case scenario that can leave you stranded with major engine damage. Because of the obvious danger, you will know immediately if your car stops running abruptly, that you need to have a full inspection of all running components including the timing belt.

If you're not sure about your timing belt or if you think there may be a problem, let our expert mechanics at Ace Auto Repair in West Jordan, Utah check things out for you. Don’t let time run out, contact us today for a FREE Repair Quote.

Download PDF

When It's Important to Get an Anti-Freeze Flush

Adding Antifreeze - Antifreeze Flush Services in West Jordan, Utah

When is it time to get your anti-freeze flushed? If you're a new car owner, perhaps you don't know what an anti-freeze flush is. Let me explain. An anti-freeze flush is the same as a cooling system flush, and it really is good for your vehicle. It removes rust, dirt, sludge, and dirty coolant from your radiator, water hoses, water pump, and all your engine's cooling passages. And, of course, a coolant flush is helpful, too. It's a flush that adds cleaner to the coolant system, in order to remove sediment and rust. Then, the system is flushed thoroughly, and new anti-freeze is added to your car. 

What is Anti-Freeze?

Coolant, a 50/50 mix of anti-freeze and water, flushes out your car's cooling system and is definitely part of a regular maintenance for your car. It prevents your engine from getting too hot. This, in turn, means you won't be sitting on the edge of the road waiting for a tow truck! If you only drain your radiator or fill it, you won't be getting to the crux of the problem, though. You'll definitely need to do a complete flush to get to the core of your problem, and this is necessary to prevent your car from getting way too hot and breaking down on you.

When Its Important To Have An Antifreeze Flush?

Anti-freeze is a product that flows through your coolant system and keeps your engine and cooling services in your car at the right temperature. If your anti-freeze gets too low or too dirty, it can be one of the main overheating engine causes, which is just about the last thing you want. If your engine overheats in today's world, it's sure to lead to a huge meltdown, and you're sure to have to spend your hard-earned money on expensive repairs to get your car back to normal. If your coolant isn't changed regularly, there will be several signs that you can look for, to make sure you get your coolant checked out:

  • Low coolant warning light
  • Engine temperature gauge is red zoned
  • Low coolant levels, if you check yourself
  • Steam leaking from under your hood
  • Overheating engine
  • Cold air coming out of your heating vents (instead of hot air)

If you notice any of these things, it's super-important to get your anti-freeze flushed, or at least come have your vehicle checked out by one of our mechanics at Ace Auto Repair in West Jordan Utah. You want to make sure you avoid, at all costs, the meltdown that can occur when your coolant levels get dirty or low. You will save yourself money if you get your coolant checked and refreshed regularly, and you're sure to avoid the same kinds of things that you hear about from folks you know who've spent ALL their money repairing their vehicle.

How Often Do You Need To Change Your Coolant?

If you're wondering, just by chance, how often you need to change your anti-freeze, here are some tips. If you have the owner's manual to your car, you can start by looking at it, but sometimes, the easiest thing to do is just to check under your hood and look at your coolant levels. You can easily see if you need to get more coolant. If your coolant levels are less than desirable, it will look brown and a lot less clear. If your coolant levels are desperate level, then it will be really sludgy. You'll know then that you need to change it as soon as you can, and getting a coolant system flush is by far the best way to go to make sure your vehicle is ready to be up and running safely again.

Let Ace Auto Repair Handle Your Cooling System with an Antifreeze Flush

At Ace Auto Repair, we have been rated the #1 auto mechanic in West Jordan Utah and would love to take care of your coolant flush for you.

If your car is showing signs of needing the Anti-Freeze flushed, stop by Ace Auto Repair in West Jordan, Utahfor a free repair quote. Feel free to give us a call at (801) 803-6016 for any questions!

Download PDF

What to Do if Your Car Overheats

Overheating engine photo - Engine overheating reasons

There's nothing worse than driving down the road and having your car overheat. Seeing steam coming from under the hood while red warning lights start to flash on your dashboard can get any driver's blood pumping. That's why it's a good idea to know why your car can overheat and what to do when and if it does.

Most Common Cause of Engine Overheating

There are many reasons your car may overheat. When your car overheats, it means that something is making it difficult for your vehicle's cooling system to do its job. Here are three of the most common overheated engine causes:

  • Coolant Concentration out of Whack: Each vehicle has its own needs when it comes to the type of coolant and the mix of coolant and distilled water. If this is off, it can result in overheating. Be sure to check your car's manual to determine the best concentration.
  • A Leaking Cooling System: A leak in your cooling system is the most common reason for overheating. The leak can be in a number of areas such as the head gasket, radiator, heater core, water pump, or some other area. A pressure test should be able to determine whether or not you have a leak.
  • Malfunctioning Thermostat: The thermostat is actually a value that is heat-sensitive. It opens and closes depending on the temperature of your engine. When in the open position, coolant is sent to the radiator. When closed, coolant remains in the engine. When the thermostat is stuck closed, your car overheats.

Additional reasons your car may overheat include:

What to Do If Your Car Overheats

Regardless of your engine overheating reasons, once it does, you need to take a few steps to ensure your safety and to keep your car from suffering additional damage.

  1. Find a safe place to pull over as soon as possible. You don't want to drive your car further than a quarter mile. Be sure to turn your car off.
  2. Wait until the temperature gauge falls to cool. You do not want to open your hood while there is still steam coming out of it. Also, you never want to try to remove your radiator cap when it is hot.
  3. Once your engine is cool, check the level of your coolant. Remove the cap and if your coolant is low, go ahead and refill it and replace the cap.
  4. Check the hoses, both the lower and upper radiator hose as well as the heater hoses for blockage or to determine if they have become disconnected or if they have burst.
  5. Go ahead and restart your vehicle.
  6. Watch your temperature gauge. If it begins to rise again, you will need to pull over once more and shut off the vehicle. At this point, it will be necessary to have your vehicle towed to a professional such as Ace Auto.

Ace Auto Repair in West Jordan Utah Will Fix All Your Overheated Engine Damage

From overheated engines to engine rebuilds and even AC recharging, here at Ace Auto Repair Utah, we can handle any vehicle repairs you may need. Our team of trained professionals makes it their mission to get you and your vehicle back on the road as soon as possible. So, if you are in the Salt Lake City area, know that we can service any make or model car or truck, and we're here to help. Give Ace Auto Repair in West Jordan a call today at: (801) 803-6016 if you need your car or truck towed, or contact us here to schedule an appointment.

Download PDF

Ace Auto Repair Has Moved to West Jordan, Utah

Ace-auto-repair-utah-new-location

Ace Auto has Moved to West Jordan, Utahj

Ace Auto Repair is excited to announce that we have officially moved to a new and improved automotive shop, conveniently located in West Jordan. Our new facility has more space in the shop for using the latest state-of-the-art equipment in auto repair. We also have more parking for the customers and perhaps best of all, you no longer have to travel down a bumpy dirt road to get to us.
Ace Auto Repair in West Jordan Utah

Ace Auto's New Address is:

Ace Auto Repair

3399 West 8395 South

West Jordan, UT 84088

 Although our address has changed, our commitment to quality auto repair services at honest, affordable rates has not. If you are in the area, we would love for you to stop by for a visit.

Small Engine Repair Service Now at Ace Auto

Ace Auto Repair is a family owned business known for providing honest and reliable auto repair services on all makes and models of cars, trucks, and SUV’s; and Now, our customers can count on Ace Auto for all of their small engine repair needs as well.

Our small engine repair mechanics have been trained to diagnose and fix small engines accurately. Our small engine repair services can help you repair your lawn mower, pressure washer, ATV, chainsaw and more. Visit our service page here for more information about our small engine repair services in West Jordan, Utah.

The Ace Auto Repair Difference

Here at Ace Auto, we pride ourselves on honest and reliable engine repair. We do not tell a customer to fix something that does not need to be fixed, we always keep them informed through the entire process, and will not perform any work without consent.

To experience the Ace Auto Repair difference for yourself, give us a call at 801-803-6016 today!

Ace Auto Repair Now Offering Small Engine Repair in West Jordan

Small Engine Repair West Jordan, UT

Small Engine Repair West Jordan, UT

Maybe you need to aerate your lawn before winter hits, or maybe you need to repair your ATV; whatever the case, Ace Auto Repair is here to help.

Ace Auto Repair now offers full-service repair and maintenance on small engines in our West Jordan location. Our trained mechanics are experienced in all makes and models, from chain saws and lawn mowers, to jet skis and motorboats; we’ve got you covered.

Our Small Engine Mechanics Can Help You:

  • Perform routine maintenance
  • Test and inspect malfunctioning engine components
  • Repair and replace worn or defective engine parts
  • Reassemble small engines
  • Provide accurate records or inspections, testing, work performed, and parts

Click HERE to learn more about our Small Engine Repair Services in West Jordan, Utah

Readying Your Car for Summer

Readying Your Car for Summer - Ace Auto Repair in West Jordan, Utah

Car on Beach - Summer Cars

With summer on its way, it's time to start thinking about readying your car for the heat and all its glorious travel opportunities. With a little preparation, you can be ready for a spur of the moment weekend getaway, and have the confidence that your car will get you there and back safely.

Keep Tires in Great Shape for Hot Pavement Grip

Winter weather can be hard on tires. This is a good time of the year to do a quick check on your tires. This should include inspecting the tread and verifying proper inflation. Poorly inflated tires impact grip which makes driving feel more erratic, can reduce your overall miles per gallon, and can even lead to a tire blowout. Always check tire pressure with a calibrated tire pressure gauge.

If you live in an area that permits snow tires, now is a good time to change them out for your standard warm weather tires. Also, check up on your spare. Make sure one is present, the correct spare for your ride, and that you have the tools to put it in should a tire blow.  Nothing is quite as awful as discovering a missing jack at 3 am with a blown tire in the middle of nowhere.

Lubrication Keeps Pistons Pumping

Oil is another area that sometimes gets overlooked. Check the oil and adjust to suit the needs of your car. Your owner's manual for your car will list recommendations for your climate. Warm oil is thin oil, and oil that is not thick enough won't provide the lubrication necessary to keep your engine in good working order. If a dealership or garage does your oil change, ask after the viscosity of oil they are using to double check it’s the right version for your needs.

Keep Your Engine Cool in the Hot Sun

Overheating is a primary cause for summertime breakdowns. One great method to reduce the risk of this is to keep on top of your coolant maintenance. Your radiator should be flushed completely and refilled every other year and you should check the level, general condition, and concentration of the coolant once in a while between replacements. If you do the flushing yourself, dispose of the old coolant properly; it has a sweet taste that dogs love and it is highly toxic.

Transmission Fluid Keeps You Shifting Smoothly

You want to keep an eye on your transmission fluid levels as well. Too much or too little, and you will run into problems that can, over time, lead to costly repairs. Further, make sure you read your manual to determine the correct mix of transmission fluid for your car. The SAE number found there will determine the right ATF mix.

Signs of too much transmission fluid:

  • Rough shifting. It will feel harder to jump from gear to gear.
  • Slippage. The engine will rev but your car won't respond.
  • Erratic behavior while shifting.

Signs of too little transmission fluid:

  • Failure to engage. The car will act like it's permanently in neutral.
  • Slow shifting. A sluggish response between gears.
  • Lurching and surging. Picking up speed rapidly then dropping back down while switching gears.

Enjoy a Frosty Interior on a Blistering Day

On a swelteringly hot day, you want your A/C in good working order. If it's not blowing a nice frigid blast through your car, you likely are in need of additional refrigerant. Ace Auto Repair can help charge your A/C if it's not keeping you nice and cool.

Summertime Tune-up West Jordan, Utah

As they say, an ounce of prevention is worth a pound of cure. Don't get stranded this summer on the side of the road with a smoking car. Bring your car into Ace Auto Repair in West Jordan, Utah for a summertime inspection, and we will check every element of auto maintenance listed above.  Avoid summertime sadness and give your ride the basic service it requires to keep you on the road.

Download PDF

What You Need to Know About Transmission Slipping and Your Car

Slipping-transmission-mechanic-kearns-utah

Transmission Gears

A slipping transmission is a sign that your vehicle needs maintenance or repair. It is not always a sign that the transmission is failing, but a slipping transmission should never be ignored. We’ve compiled some basic signs and symptoms of a transmission slip, as well as what to do if your transmission is slipping.

What Does a Car’s Transmission Do?

To figure out if your transmission is slipping, it helps to understand the purpose of a car’s transmission and a little bit about how it works. The transmission transfers the energy produced by the car’s engine to the wheels. The internal combustion engine of your vehicle creates power and the transmission converts that power into torque, or rotational energy. The torque is then conveyed to the axles and rotates the wheels.

What is a Slipping Transmission?

When a transmission slips, it is not properly transferring the energy from the engine to the wheels. It may feel like the vehicle is slow to respond, or does not respond at all when you press the gas pedal. Or it could feel like your car changes gears suddenly without any apparent reason.

Common Signs of a Slipping Transmission

It is not always easy to diagnose a slipping transmission. There are a few common signs that you should definitely not ignore. Some of the more commons signs of a slipping transmission include:

  • Engine revving, specifically RPMs (revolutions per minute) that exceed 3,000-3,500
  • A high-pitched whistling noise from the engine with grinding sounds
  • Delayed acceleration
  • Delay when shifting from park to drive or reverse
  • Car shifting at unexpected times
  • Loss of engine power

How to Fix a Slipping Transmission?

A transmission can slip for several different reasons and some of the causes are far easier to fix that others. For example, a clogged transmission filter, low transmission fluid, or even burnt transmission fluid can all cause a transmission to slip and are not that difficult to fix. You’re looking at a more severe problem however if the transmission slips as a result of worn or broken transmission gears or bands.

Since low or ineffective transmission fluid is a likely cause of a slipping transmission, it can make a world of difference to do a transmission flush. This is when an ASE-certified technician flushes the transmission with fresh transmission fluid and cleans the entire system. Any burnt or ineffective fluid is flushed out. A transmission flush can also get rid of any contaminants that may have been preventing the proper flow of transmission fluid.

There are transmission fluid additives available that can help, to an extent, with some transmission slipping. These additives can help to improve friction or remove varnish buildup in the transmission. They cannot repair damaged gears or other internal parts of your transmission. Additionally, you should not use any transmission additive that contains solvents. Solvents can cause the seals in your transmission to wear more quickly by lowering your transmission fluid’s lubrication.

If you have had a transmission flush and tried an additive to no avail, you may have a serious transmission problem. The clutch may need to be adjusted or replaced. The bands may need adjustment or replacement. The gears themselves may even need to be replaced. In any of the instances, the transmission must be dismantled to perform these repairs.

Slipping Transmissions in West Jordan, Utah

If you think your transmission is slipping, it is better to deal with it now than to wait until later. A transmission slip that can be resolved with a transmission flush today may require more costly repairs in the very near future. If you are around West Jordan, UT and have any signs of a slipping transmission, contact Ace Auto Repair today. We’ll help get you and your vehicle back in gear.

ASE Certified Mechanic in West Jordan, UT
We accept these major credit cards

 

 

Download PDF

How to Avoid Being Ripped Off By a Dishonest Mechanic

spotting-Dishonest-Mechanic

spotting-Dishonest-Mechanic

"Hey, does anyone know of a good mechanic?"  We frequently hear this from our acquaintances or see this post on social media.  Car repairs can be expensive, and, as consumers, we want to make the best choices possible when it comes to automotive services.  Word of mouth is one way to find a good mechanic, but perhaps we should ask the larger question, "how do we avoid being ripped off by a dishonest mechanic?"

Know Your Vehicle

Start by looking to your owner’s manual for regular maintenance recommendations.  Dishonest mechanics know that the easiest people to rip off are the ones who know nothing about their cars or what is being done to it. When you lack knowledge on a subject matter, you're more likely to believe whatever you're told, and therefore, stand a higher chance of being ripped off.

Ask Questions, Questions, and More Questions

A great mechanic wants his customers to be well educated about their vehicle and the services he provides.  Ask him to describe the vehicle’s problem in detail, including what should be done to fix it, what parts will need to be replaced, and how the problem affects the vehicle’s overall performance.  If you do not understand something, make sure to ask follow up questions to clear up any inconsistencies or misunderstandings.  A great mechanic will be eager to explain repairs to you and answer your questions; after all, it’s an opportunity to show off his expertise!

Ask to Have the Old Parts Returned to You

If a mechanic tells you that you need to replace a part, ask to see the part that needs to be replaced. Some "mechanics" will tell you that you need a part replaced, and then bring you the part, but it is not actually the one from your car. If have any suspicions, you can even ask to go back in the garage so you that you can examine the vehicle yourself.   When a mechanic knows that you want the broken stuff back, the mechanic is more likely to actually do the work even he originally had plans for dishonesty.

Read Online Reviews About the Repair Shop

Along with traditional word of mouth recommendations, online reviews are an excellent way to gather information about your mechanic.  Start with a general Google search to read online reviews of the mechanic’s shop.  Searching the mechanic by shop name along with the city and state will yield some important information including internet posts by satisfied and unsatisfied customers.  Read all posts carefully.  A single unhappy customer does not necessarily mean the mechanic is dishonest, but a pattern of unhappy customers means you should steer clear of this particular shop.  Google+, Yelp, and the Better Business Bureau’s online search tool are excellent ways to gather information about your potential mechanic.

Get a Detailed Auto Repair Estimate in Writing

A detailed written estimate is critical to have in hand prior to authorizing the performance of any service work.  Have the repair shop give you an estimate of exactly what they will be doing, what they are replacing, the tests they will be doing (if any), the parts they plan to replace and the amount of time they think it will take.  A written estimate amounts to a basic contract in most states and protects the consumer from unauthorized work and expenses.  With an agreed upon written estimate, the mechanic cannot perform any repairs that are not on the estimate without your approval.  Just as you would never sign a blank check and hand it over to your mechanic, NEVER sign a blank authorization form.

Check for Mechanic Certificationsase

Just as you would expect from any professional, the mechanics who work on your vehicles should have industry certifications.  Look for ASE certifications.  Possession of such certification means that your mechanic has passed rigorous testing to prove their expertise in auto repair.  A mechanic who has not passed these tests should not be allowed to work on your vehicle.

Honest Mechanics West Jordan, Utah

Leave dishonest mechanics in the dust.  Looking for honest mechanics in West Jordan, Utah?  Visit us online at Ace Auto. We provide free written estimates and a guarantee on all of our work.  Give us a call at 801-803-6016 to discuss your automotive repairs or schedule an appointment today.